Another way to add a Bench Stop to a Bench.

Most woodworkers have at one time or another encountered the object pictured above. Some shy away due to the bad press accredited to these contraptions. Others seem to have rows installed on their bench without much issues.

3 words that worry more woodworkers more than " concealed mitered dovetail" , Taiwan is still better than modern China made hardware, in general. These came from a UK merchant on ebay.

These used to be made out of steel. I've seen one by Wm Marples going for more than a song on ebay. The biggest issue with these stops lies in the material now being used: Cast Magnesium/Zinc/Aluminium Alloy. I do not know which of the 3, but I do know it is CAST. Yes, including the threaded rod controlling the lift of the jaws.

Strength is the issue.

This even has a recess for any bulk buyer to put their trade label.

I recall countless times of needing something to butt against while planning a small, thin strip of wood, such as the side of a small box. Hence the jig below.
I could have simply mortised directly into my bench, but where I wanted the stop, there's concealed threaded rods, vise mounting lag screws.

Here I start mortising a length of stock. This planning jig will accommodate stocks up to 12" long, 4" wide.

Below: The cleat is PVA glued and screwed in a diamond formation; for no particular reason.

This is how the planning jig will be deployed.

Below: A close up of the innards.

Most short, thin, difficult boards shall be bullied into submission.

Prime cuts from: Far Eastern Wood Butcher.

Comments

SHARPENING WITH ARKANSAS STONES

What on earth are they? A user made box of assorted Arkansas stones. They are America's answer to: The Wales' Welsh Slate (Dragon's Tongue); The Scotch Tam O'Shanter; The English Charnley Forest stone; The Japanese Tenin Toishi; The German Thuringian Hone; The Chinese Guangzhou River bedrock; The Belgian Coticule; You get the idea. Local rocks that you use to sharpen mama's kitchen knives. A collection of smaller pocket-sized Arkansas stones In this entry, I will not try to tell you what you probably already know. What is the point of describing that oily rock you already have under your bench, in your drawer, in a can of kerosene? Note also, that the sharpening I describe here is best applied to woodworking in general. I am an amateur handtool woodworker. Sharpening a straight razor would be entirely another branch of science. I do not profess to know all there is to know about sharpening or Arkansas stones; I simply failed ...

The prolific & seemingly mundane Stanley 110 block plane..

R eally? Well, it's everywhere, check Granpa or uncle Tim's shack ( if you include copies of it by lesser tool makers) For something so abundant (well, Stanley sold them by truckloads), so common and so relatively inexpensive, I will attempt to wax some lyrical on them. By "them" I mean their design, their construction. The plane pictured above was purchased off ebay for $4.90. It looked like Joe Meatball (to borrow Patrick Leach's character) bought it, used it on some hardwood (pre silicon valley micro chipping at the edge)without first fettling the plane(unsharpened factory bevel), and put it away (in some dry place), and totally forgot about it. First off, at Five Bucks, how can you go wrong? Five bucks don't buy you a door wedge these days. STANLEY'S SUPERIOR ADJUSTABLE HEIGHT DOOR WEDGE, TYPE 16. 1) The lever cap also serves as an ergonomic palm-rest to push the plane forward, and the oval shaped cut-out serves as a hanging h...

10 Things I learnt about Arkansas Stones

10 things I learned about Arkansas stones Stones should be kept in their own box, or in a segregated box. This keeps out saw dust, and protects from stones knocking on each other, causing chips. 1) Not for sharpening tools: Not a typing error too. I'm sure everyone has a dull knife or two in the kitchen. The type that will not cut meat or slice bread. You may be able to push-cut an apple, but that's all it'll do. Or that vintage ebay Marples chisel or that plane iron off a vintage Bailey. The edges on these tools will need to be dressed (chips ground-out, skew-edge squared, rolled-edge removed) and re-profiled (irregular and multiple bevel angles corrected) on a bench grinder or a coarse diamond plate, carborundum stones etc. All the above before it even touches an Arkansas stone. I have never met an Arkansas stone that can remove chips or correct bevel in less than 2 hours. Use Arkansas stones for honing and polishing. Old timers call it ...

The Far-Eastern Wood Butcher: Prime cuts from the far east.

Search This Blog