Skip to main content

SURVIVAL KNIFE MODIFICATION: SCHRADE SCHF 9 RE-HANDLE

 
One of the series of knives released by Schrade (Taylor Brands) in 2015 that has created some stir, mainly due to their low price and choice of blade steel. Probably also due to their quarter inch thick spine. For this SCHF 9, well two more notables: Recurved edge (love it or hate it) and Flat-ground main bevel.
 
The TPE (Thermo Plastic Elastomer) handle is held together by 8 individual  Hex bolts threaded into the tang, though it looked like four bolts only.
 
 
 I noticed that manufacturer who stamped their marks tends to laser them later on their subsequent release. Perhaps to reduce cost? They usually cite material strength issues caused by hard stamps (A stamp applied forcibly on a ricasso may weaken the knife or bend it slightly. Well, for this Schrade, they stamp it where the fuller (blood groove) would have been, so it's not a material-strength compromise we are dealing with here. Looks more like cost issue. Well, at below $40, Schrade had a good reason not to stamp it. I totally dig it.
 My first impression holding the knife in the palm of my hands (I have average sized hands) is that the palm swell feels bulky. The feel is like someone wrapped an extra roll of Wilson racquet tape on a racquet handle which already had some existing tape.
 The hex bolts come in 3 different lengths, to compensate for the uneven TPE handle thickness.
A close-up view of the tapped recess to engage the hex bolts. Now, I have decided to play mountain man. (or Jungle man for SE Asian readers)


Above: some tools and materials I used to rehandle the handle in TEAK. The file handles were shown here to illustrate the finish I intend to achieve with the important looking Da



Above: The blade was cold-blued. The teak handle was peened with 1/8" brass rods.



Above: The laser etch is still visible after the cold-blue was applied.



The primary bevel was given a Kanaban Grind: flat piece of mild steel and some powdered Aluminium oxide mixec with water(crushed powdered carborundum stone, if you will) This produces a hazy steel look, like a laminated Japanese Hunting knife.


After the abortion, the knife felt much better in my hands.


I had a good supply of paracords, but this worn shoelace looked the part more as a lanyard. Also shown is the black Nylon sheath. (This knife does not come with a diamond hone and ferrocerium rod like the SCHF 51 & 52s)

All in all, I thought I made the knife more inviting to use, and more natural to look at. What do you think?

Regards from lion city.

Comments

  1. AnonymousAugust 3, 2023 at 10:50 AM

    Excellant! The original TPE plastic handle needs to go. Pleased to see that the tang is not skelatized like Eafengrow.

    ReplyDelete

Post a Comment

Popular posts from this blog

SHARPENING WITH ARKANSAS STONES

What on earth are they? A user made box of assorted Arkansas stones. They are America's answer to: The Wales' Welsh Slate (Dragon's Tongue); The Scotch Tam O'Shanter; The English Charnley Forest stone; The Japanese Tenin Toishi; The German Thuringian Hone; The Chinese Guangzhou River bedrock; The Belgian Coticule; You get the idea. Local rocks that you use to sharpen mama's kitchen knives.   A collection of smaller pocket-sized Arkansas stones  In this entry, I will not try to tell you what you probably already know. What is the point of describing that oily rock you already have under your bench, in your drawer, in a can of kerosene? Note also, that the sharpening I describe here is best applied to woodworking in general. I am an amateur handtool woodworker. Sharpening a straight razor would be entirely another branch of science. I do not profess to know all there is to know about sharpening or Arkansas stones; I simply failed ...
31 comments
Read more

The prolific & seemingly mundane Stanley 110 block plane..

R eally?   Well, it's everywhere, check Granpa or uncle Tim's shack ( if you include copies of it by lesser tool makers) For something so abundant (well, Stanley sold them by truckloads), so common and so relatively inexpensive, I will attempt to wax some lyrical on them. By "them" I mean their design, their construction. The plane pictured above was purchased off ebay for $4.90. It looked like Joe Meatball (to borrow Patrick Leach's character) bought it, used it on some hardwood (pre silicon valley micro chipping at the edge)without first fettling the plane(unsharpened factory bevel), and put it away (in some dry place), and totally forgot about it. First off, at Five Bucks, how can you go wrong? Five bucks don't buy you a door wedge these days.   STANLEY'S SUPERIOR ADJUSTABLE HEIGHT DOOR WEDGE, TYPE 16.  1) The lever cap also serves as an ergonomic palm-rest to push the plane forward, and the oval shaped  cut-out serves as a hanging h...
20 comments
Read more

10 Things I learnt about Arkansas Stones

10 things I learned about Arkansas stones Stones should be kept in their own box, or in a segregated box. This keeps out saw dust, and protects from stones knocking on each other, causing chips. 1)  Not for sharpening tools: Not a typing error too. I'm sure everyone has a dull knife or two in the kitchen. The type that will not cut meat or slice bread. You may be able to push-cut an apple, but that's all it'll do. Or that vintage ebay Marples chisel or that plane iron off a vintage Bailey. The edges on these tools will need to be dressed (chips ground-out, skew-edge squared, rolled-edge removed) and re-profiled (irregular and multiple bevel angles corrected) on a bench grinder or a coarse diamond plate, carborundum stones etc. All the above before it even touches an Arkansas stone. I have never met an Arkansas stone that can remove chips or correct bevel in less than 2 hours. Use Arkansas stones for honing and polishing. Old timers call it ...
Post a Comment
Read more